Barista Basics Complete Rinser Install Kit for Countertop and In-Counter Installation

Everything You Need. One Kit. No Hardware Store Run.

Installing a commercial pitcher rinser means running a cold water supply line and a drain connection. You can source those components individually, or you can grab the Barista Basics Complete Rinser Install Kit and have everything in one order.

This kit is put together specifically for Barista Basics commercial rinsers and includes the fittings, tubing, and hardware needed for a standard countertop or in-counter installation. It works for both setups and covers the components that come up in nearly every install. Open the box, follow the installation guide, and get the rinser running without a separate trip to the plumbing supply house.

Compatible with the following Barista Basics rinsers: EPPR724, EPPR715, EPPR662, EPPR6102, EPPRCT662, and EPPRCT6102.

Note: if your incoming water pressure exceeds 30 PSI, you will need a pressure regulator in addition to this kit.

What's in the Kit

• 5-Foot Drain Hose, 16mm Diameter (qty: 1)
  Connects the rinser drain outlet to your under-counter drain line. The 16mm diameter is sized for the 1.5" barb drain fitting on Barista Basics rinsers and handles drainage volume at full operating pressure without restriction.
• 10-Foot Flexible John Guest Tube, 3/8" Diameter (qty: 1)
  Runs the cold water supply from your shutoff valve to the rinser inlet. Ten feet gives enough length to route cleanly through most countertop and in-counter setups without splicing.
  
• John Guest Angle Stop Adaptor Valve (qty: 1)
  Connects to your cold water supply line and gives you a dedicated shutoff for the rinser. Lets you isolate the rinser for service or maintenance without cutting water to the rest of the bar.
  
• John Guest Straight Check Valve, 3/8" x 3/8" (qty: 1)
  Prevents backflow in the supply line. Required in most installations and sometimes mandated by local plumbing codes alongside a backflow preventer.
  
• 1/2" 90-Degree PP Insert Elbow (qty: 1)
  For installations where the drain hose needs to make a sharp turn in a tight space under the counter. Not used in every install, but included so you have it if the run requires it.
  
• 3/8" x 3/8" John Guest Union Elbow (qty: 1)
  For supply line runs that require a direction change. Connects two sections of 3/8" John Guest tubing at a clean 90-degree angle without reducing flow.
  
• 3/8" John Guest Locking Clips (qty: 5)
  Secure John Guest press fittings and prevent accidental disconnection under pressure. Standard practice on any John Guest installation in a commercial environment.
  
• 7/16" to 1.0" Hose Clamps (qty: 4)
  Secure the drain hose to barb fittings at both ends. Adjustable range covers the standard fitting sizes included in this kit.

Specifications

• Drain hose: 5 feet, 16mm diameter.
• Supply tube: 10 feet, 3/8" John Guest.
• Angle stop adaptor: John Guest, cold water.
• Check valve: John Guest straight, 3/8" x 3/8".
• 90-degree elbow: 1/2" PP insert, for tight-space drain routing.
• Union elbow: John Guest, 3/8" x 3/8".
• Locking clips: 3/8" John Guest, qty 5.
• Hose clamps: 7/16" to 1.0" adjustable, qty 4.
• Compatible rinsers: EPPR724, EPPR715, EPPR662, EPPR6102, EPPRCT662, EPPRCT6102.
  

Who the Barista Basics Complete Rinser Install Kit Is For

This kit is for anyone installing a Barista Basics commercial rinser who wants a clean, complete install without sourcing individual components.

It's the right fit for:

• Bar builders and contractors installing rinsers as part of a new bar build or renovation who want all fittings in one order.
• Café and restaurant operators self-installing a rinser and want the right parts the first time without guesswork.
• Anyone replacing an existing rinser and refreshing the supply and drain connections at the same time.
• Operations adding a second rinser station and needing a complete fitting set for the new run.

How the Barista Basics Complete Rinser Install Kit Compares

Barista Basics Complete Rinser Install Kit vs. Sourcing Parts Yourself
Sourcing installation components individually is a legitimate option. John Guest fittings, drain hose, and hose clamps are available through plumbing supply houses, restaurant equipment distributors, and online retailers. Experienced bar builders and plumbers often have preferred suppliers and may already have some of these components on hand.

The tradeoff is time and compatibility. Sourcing individually means confirming that each component is the right diameter, the right fitting type, and the right length for your specific rinser before ordering. It means multiple line items, potentially multiple suppliers, and the risk of a component arriving wrong or short and delaying the install.

The Barista Basics Complete Rinser Install Kit removes that process entirely. Every component is selected specifically for Barista Basics rinsers and sized for a standard countertop or in-counter installation. One order, one delivery, one install.

Choose DIY sourcing if you have an established plumbing supplier relationship, components already on hand, or specific installation requirements that call for custom runs. Choose the Barista Basics Complete Rinser Install Kit when you want the right parts in one order and the rinser running the day it arrives.

Key Takeaway
DIY sourcing wins on flexibility and cost if you already have supplier relationships and components on hand. The Barista Basics Complete Rinser Install Kit wins on convenience, compatibility, and time. For operators who want a clean install without a separate sourcing process, this is the kit that makes it straightforward.

Why Espresso Parts Recommends the Barista Basics Complete Rinser Install Kit

We built this kit because we watched too many rinser installs get delayed or complicated by missing fittings. A café operator orders the rinser, it arrives, and then someone has to make a separate trip to the plumbing supply house for a check valve or the right length of John Guest tubing. The bar doesn't open on time. The install gets pushed.

The Complete Rinser Install Kit exists to close that gap. Every component in it is sized and selected specifically for Barista Basics rinsers. The tubing length, the drain hose diameter, the locking clips, the hose clamps: all of it is chosen for the install you're actually doing, not a generic assortment of plumbing parts that may or may not work together.

You can source these components individually. Plenty of operators do. But if you want the rinser running the day it arrives without a separate order or a hardware run, this is the kit that makes that happen.

Frequently Asked Questions

Q: Is this kit required to install a Barista Basics rinser?
A: The rinser requires a cold water supply connection and a drain line hookup to operate. This kit includes the components needed for a standard installation. You can source the parts individually if you prefer, but this kit puts everything in one place and is sized specifically for Barista Basics rinsers.

Q: Does this kit work for both countertop and in-counter rinser installations?
A: Yes. The components in this kit cover both countertop and in-counter installations. The 90-degree drain elbow is included for tight-space installs but is not required in every setup.

Q: What if my water pressure is over 30 PSI?
A: If your incoming water pressure exceeds 30 PSI, you will need a pressure regulator in addition to this kit. Running the rinser above 30 PSI can damage the internal seals and affect performance.

Q: Is an installation guide available?
A: Yes. A detailed rinser installation tutorial is available to walk you through the full setup process.

Q: Which rinsers is this kit compatible with?
A: This kit is designed for the following Barista Basics rinsers: EPPR724, EPPR715, EPPR662, EPPR6102, EPPRCT662, and EPPRCT6102.

Q: Does Espresso Parts offer support if I run into installation questions?
A: Yes. As the makers of the Barista Basics line, we support every product we sell. If you run into questions during installation, reach out and we'll help you work through it.

About Barista Basics

Barista Basics Barista Basics is Espresso Parts' own line of professional coffee and bar tools, built for the demands of commercial service. The Complete Rinser Install Kit is part of that same philosophy: the right components, sized correctly, in one place, so the install goes smoothly and the rinser gets to work faster.